STUDI KARAKTERISTIK PEMBAKARAN MINYAK PIROLISIS PLASTIK MENGGUNAKAN STEAM-ATOMIZING BURNER
DOI:
https://doi.org/10.34151/technoscientia.v10i2.101Keywords:
Air pressure, LDPE, Pyrolysis, Steam-atomizing burnerAbstract
One of the new and renewable energy resources is Plastic Pyrolysis Oil, that produced from pyrolysis process of plastic wastes. This oil could be utilized as energy source using steam-atomizing burner, which it burning characteristics dependent to air pressure that used in the burner. The objective of the research was to investigate the influence of air pressure on the burning characteristic of plastic pyrolysis oil using steam-atomizing burner. The raw material that used are dry LDPE wastes. First, it was heated in pyrolysis reactor using biomass combustion as energy source, produced pyrolsyis oil, noncondensable gases, and carbon black. The oil that produced is used as fuel for combustion in steam-atomizing burner, to know it burning characteristic, with variable air pressure on 1, 2, 3, 4, and 5 bar. The observation was made on fire temperature, the long of flame, and it efficiency, that showed by fuel consumption in burner and yield of plastic pyrolysis oil that produced. The experiment results showed that as the air pressure increased, all parameters were increased, that are fire temperature, the long of flame, fuel consumption in burner, and the yield of plastic pyrolysis oil that produced in the pyrolysis reactor.
References
Cahyono, M.S., 2013, Pengaruh Jenis Bahan pada Proses Pirolisis Sampah Organik menjadi Bio-oil sebagai Sumber Energi Terbarukan, Jurnal Sains dan Teknologi Lingkungan, Vol. 5, No. 2, Juni 2013, hal. 67-76.
Curtis, A., 2001, Assesment of The Effect of Cumbustion Waste Oil, and Health Effect Associated with The Use of Waste Oil as a Dust Supresant. USA: WoodwardClyde. Ltd.
Koide, K., 1999, R&D on Central Heating System with Cracked Light Oil Fraction as The Main Fuel, Petroleum Energy Center All Right Reserved, 1999C3.1.8.
Liestiono R. P., Cahyono M. S., Widura W.W., Prasetya Agus, dan Syamsiro, M., 2017, Karakteristik Minyak dan Gas Hasil Proses Dekomposisi Termal Plastik Jenis Low Density Polyethylene (LDPE), Jurnal OFFSHORE, Vol. 1, No. 2 Desember 2017, pp. 1-9.
Mandala, W. W., Cahyono, M.S., Ma’arif, S., Sukarjo, H. B., dan Wardoyo, 2016, Pengaruh Suhu terhadap Rendemen dan Nilai Kalor Minyak Hasil Pirolisis Sampah Plastik. Jurnal Mekanika dan Sistem Termal, Vol. 1, No. 2, Agustus 2016, hal. 49-52.
Prabawa, P. A., 2010, Pengaruh Tekanan Udara terhadap Sifat Pembakaran Minyak Residu menggunakan Vaporizing Burner untuk Peleburan Aluminium. Skripsi, Universitas Sebelas Maret Surakarta.
Purwanti dan Sumarni, 2008, Kinetika Reaksi Pirolisis Plastik Low Density Polyethylene (LDPE), IST AKPRIND, Yogyakarta.
Santoso, J., 2010, Uji Sifat Minyak Pirolisis dan Uji Performasi Kompor Berbahan Bakar Minyak Pirolisis dari Sampah Plastik, Thesis, Fakultas Teknik, Universitas Negeri Sebelas Maret, Surakarta.
Syamsiro, M., Saptoadi, H., Norsujianto, T., Noviasri, P., Cheng, S., Alimuddin, and Z., Yoshikawa, K., 2014, Fuel Oil Production from Municipal Plastic Wastes in Sequential Pyrolysis and Catalytic Reforming Reactors. Energy Procedia, Vol. 47, pp. 180-188.
www.bp.com/statisticalreview2015
