Unjuk Kerja Charge Controller metode PWM Menggunakan Arduino Uno

Authors

  • Hendi Matalata Universitas Batanghari
  • Asnal Effendi Institut Teknologi Padang

DOI:

https://doi.org/10.34151/jurtek.v15i1.3957

Keywords:

Arduino, Charge Controller, PWM

Abstract

The need for a charge controller for the use of electrical energy sourced from solar panels and DC generators is very necessary for the purposes of the battery function as electric power in the inverter which functions as a voltage source. Usually the battery is used for inverter purposes in meeting household electricity needs as a substitute for PLN. The charging process will occur if the output voltage from the DC voltage source is higher than the battery voltage to be recharged. In this study, the charging process is based on PWM settings, and consists of 2 types, namely boost mode and float mode which are distinguished from the duty cycle setting. The voltage reading on the voltage divider sensor using a resistor has an error of less than 6.22% at the source terminal, and 6.89% at the battery. However, the charging process is able to provide an average voltage of 13.14 Volts on the battery (12 Volts), so that the charging process can run well.

Downloads

Download data is not yet available.

References

Achmad P.Sardju, M. Y. A. (2021). Perancangan Charge Controller. Journal Of Science And Engineering, 4(1), 47–52.

I Gusti Ngurah A M, I. W. A. W. Dan I. W. R. (2016). Rancang Bangun Baterai Charge Control Untuk Sistem Pengangkat Air Berbasis Arduino Uno Memanfaatkan Sumber Plts. E-Journal Spektrum, 3(1), 26–32.

Johar, L. W. (2020). Desain Charger Control Pembangkit Listrik Tenaga Hybrid Dengan Pengaturan Duty Cycle Pwm. Journal Of Electrical Power Control And Automation (Jepca), 3(2), 49. Https://Doi.Org/10.33087/Jepca.V3i2.40

Junaldy, M., Sompie, S. R. U. A., Patras, S., Elektro, T., Sam, U., Manado, R., & Manado, J. K. B. (2019). Rancang Bangun Alat Pemantau Arus Dan Tegangan Di Sistem Panel Surya Berbasis Arduino Uno. Jurnal Teknik Dan Komputer, 8(1), 9–14.

Matalata, C. Y. S. Dan H. (2018). Perancangan Boost Converter Dengan Ldr Sebagai Pengendali Sinyal Pwm Untuk Menaikan Tegangan Panel Surya. Journall Of Electrical Power Control And Automation, 1(2), 39–44. Https://Doi.Org/10.33087/Jepca.V1i2.9

Mirzazoni, A. Dan I. N. (2020). Pengaruh Intensitas Cahaya Dan Temperatur Terhadap Serapan Energi Matahari Untuk Pembangkitan Daya Listrik Di Kota Padang. Jurnal Teknologi, 12(2), 104–108.

Prasetyo, K. A. (2018). Pengembangan Alat Control Charging Panel Surya Menggunakan Aduino Nano Untuk Sepeda Listrik Niaga. Jurnal Edukasi Elektro, 2(1), 50–58. Https://Doi.Org/10.21831/Jee.V2i1.19947

Downloads

Published

2021-06-17

How to Cite

Matalata, H., & Effendi, A. . (2021). Unjuk Kerja Charge Controller metode PWM Menggunakan Arduino Uno. Jurnal Teknologi, 15(1), 1–8. https://doi.org/10.34151/jurtek.v15i1.3957

Issue

Vol. 15 No. 1 (2022): Jurnal Teknologi

Section

Articles

License

Copyright (c) 2022 Hendi Matalata, Asnal Effendi

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Jurnal Teknologi provides immediate open access to its content in order of making research freely available to the public to support a global exchange of knowledge. All articles published in this journal are free for everyone to read and download, under licence CC BY SA. 

Benefits of open access for the author, include:

  • Free access for all users worldwide.
  • Authors retain copyright to their work.
  • Increased visibility and readership.
  • No spatial constraints.